In November of 2011 Saber Grills unveiled a line of six cart mounted gas grills and two built-in models for the entry level, premium grill category. Saber is offered in two, three, and four burner configurations. These grills are based on patented infrared designs developed by Saber’s parent company, Char-Broil and contain several noteworthy innovations. Sabers are much more sophisticated and much higher quality Char-Broils. I extensively tested a three burner stainless steel model. I was impressed. It gets real hot, real fast, and can hit 700°F in about ten minutes. Heat is uniform across the entire cooking surface. It does not flare up and produces moist, juicy foods.

The firebox is designed to cradle each burner with individual compartments for complete isolation and optimal zone cooking. Below is an illustration of one burner system. On a two burner unit there are two of these units, etc. There are no heat tents or flavor bars covering the burners. The 304 stainless grate system has a unique, patented design meant to promote uniform radiant heat and move convection heat away from the cooking grate. Convection heat is hot circulating air that can rob food of moisture. The grate/emitter system has ridges that conform to the bottom of the grates. Rather than cast metal or steel rods, the grates are half-tubes of stainless steel that fit onto these ridges and create a series of hot air tunnels. A row of slots at the peak of each ridge delivers heat from the burners below into this tunnel. The heat then naturally escapes by moving out of the tunnel and dissipates through vents at the cooking area perimeter.

saber grill burners

Despite the high heat, our three burner demo is rated at only 24,000 BTU (remember, BTU is a measure of fuel consumption and is not directly related to heat any more than fuel consumption of a car has to do with speed). Each burner is rated at 8,000 BTU. Saber’s fuel efficiency was rewarded by Hearth and Home Magazine with their VESTA 2012 Green Award for creating a grill that reduces gas consumption by 30 to 50%.

The all stainless models with seamless welds have an aesthetic appeal similar to the luxury brands, although it is much less expensive. Housings are built with solid construction that rivals many more expensive, premium grills. All stainless steel is top quality 304 grade. Cart frames are fully welded 1″ steel. All carts models have heavy duty 3″ locking casters and are built for Propane. Built-ins are set up for natural gas. EZLP and EZNG conversion kits are available. Entry level models have cast aluminum end caps.

Entry level models have a battery operated push button ignition. Premium, all stainless models have a few upgrades. Push and turn, battery powered electric ignition on each knob is smooth and consistent. Two halogen hood lamps work beautifully to illuminate the entire cooking chamber after dark. Some Sabers have an excellent dual control side burner with a two sided grate that accommodates bowl-shaped woks or flat- bottom pots. It has a large circular burner with a smaller burner at the center. The dual controls are not marked to identify the corresponding burner, but one gets accustomed to this quickly. It carries a warranty that exceeds many competitors.

Although it can’t go from 225°F to 900°F in the blink of an eye like some more expensive grills, it cranks pretty fast, making it great for the reverse sear method on steaks and burgers. Pat O’Donnell, president of Hearth and Home Patio & BBQ, is a Chicago area Saber dealer. O’Donnell has sold the venerable TEC infrared grills for many years and feels the performance of Saber for searing steaks, chops and fish is nearly as good as TEC. “There is no appreciable difference”, he states.

saber 2 burner grillThere are a few minor issues. We’ve never found accurate bi-metal dial thermometers from any manufacturer and Saber is no exception. Entry level models have one in the hood, and premium models have one above each main burner control knob. I had a couple conversations with Saber about their dial thermometers. They ultimately agreed with us that dial thermometers only provide a vague reference point. They are not accurate and “heat indicators” is a more appropriate name.

Saber models with individual burner indicators provide additional reference points that may have some use when zone cooking. They do illustrate how quickly these systems heat up. After fifteen minutes with all burners cranked to the max and the Saber dials pegged past 800°F, my Thermoworks thermocouple read 710°F. I had the probe in the center of the cook surface hovering at grate level between two grates. At that point, regardless of the actual temperature, it was plenty hot for searing. At the end of the day, nothing takes the place of an accurate digital thermometer.

I was able to get a nice whiff of smoke on steaks, fish and chicken by simply dropping wood chips into the grates. But when I set it up for 2-zone cooking with a water pan and used wood chips in foil pouches for ribs, shoulder, brisket and whole chickens, it was good, but not deep-smoked.

The Saber cook chamber is almost completely sealed off from the gas flame. In fact, I had trouble seeing the flame when I fired it up the first time, (one quickly learns to peek through a small opening above each main burner). When grilling small items like shrimp and wings, there are no worries about losing food between the grates. This closed system is instrumental for generating radiant heat and preventing flare ups, but even though I did a burn off after each session, grease accumulation eventually became noticeable inside the hood and around the edges of the grates.

Speaking of grease, the grease tray is my least favorite feature of Saber. When left in the rain uncovered, the tray fills with water. Although, not much grease gets past the grates, some does. Carrying a one inch deep two foot wide tray of greasy water across my deck required a balancing act that I barely pulled off. Avoid this nuisance by using a cover, especially when you expect rain.

Assembly was easy. You basically put the cart together then drop the head into it. This is done with twenty-six identical hex bolts, six identical screws, and some washers. The only problem occurred when the grill was almost fully assembled. Directions indicated two thin wires from the halogen hood lights should be hanging from the bottom of the grill inside the cart. They were nowhere to be found. After several minutes of confusion and frustration, I pulled out the grease tray and discovered the wires taped to the bottom of the firebox.

Rob Schwing, General Manager of Saber, told me how the powers that be at Char-Broil directed him to create a new line of premium grills from the ground up. There’s an old saying: “It can be great, it can be inexpensive, or it can be done quickly. Pick two.” Char-Broil chose great and inexpensive. Saber had to compete with other premium grills, but sell for less. Schwing was given a blank piece of paper, a pile of money and told to do what it takes to make it happen. He had the buying power and infrastructure of one of the worlds largest grill manufacturers at his disposal.

Schwing’s team immediately ordered hundreds of different grills to be delivered to the new Saber warehouse in Char-Broil’s Columbus, GA, facility. They wanted to not only analyze the best performance characteristics of each grill, but also how different designs impacted on cost, packaging, shipping and assembly. One interesting idea gleaned from this process was to pre-assemble the grill head, then wrap it with the partially assembled cart. If the box was damaged in shipping, the less expensive cart would protect the valuable grill head. All cost savings were passed along to the consumer, or used for upgrades like the 304 stainless. “From a business perspective, the time was right to introduce a line of premium grills that didn’t carry a super-premium price tag”, said Schwing. “In recent years we’ve watched high-end manufacturers degrade their materials to bring margins up. Product quality has gone down but prices haven’t.”

Saber achieves further cost reduction by using Char-Broil’s aggregate buying power although they do not use Char-Broil’s Chinese manufacturing facilities. They work with a different Chinese manufacturer that focuses on high-end metal fabrication. Schwing bristles at the perception that everything made in China is cheap. “When I go to an airport, everyone’s walking around with iPads and iPhones. The Chinese make some of the best products in the world.” Indeed, Meathead and I recently had this same discussion. It’s not that the Chinese are only capable of making cheap stuff, it’s that western companies are placing orders for an awful lot of cheap stuff with Chinese manufacturers. Not so with Saber. During the course of my tests I invited many friends and family members by to join in. None had heard of Saber yet, but the response was always some variation on “Wow! That’s a nice grill!” The quality is easy to see and easy to appreciate.

Saber is not available in any big box chains and is sold exclusively through specialty retail stores. For your nearest dealer check Saber’s website.

saber 4 burner grillR67SC0012
4 stainless steel burners for 32,000 BTU
18,000 BTU dual control side burner
Double walled stainless steel lid with seamless welds
670 square inches of primary cooking surface
225 square inch warming rack
2 internal halogen lights
Stainless steel control panel
Double door stainless steel cart
Stainless steel side tables with towel holder and tool hooks
4 burner level heat indicators
MSRP $1,699

Also available as a built-in model R67SB0312 configured for natural gas
MSRP $1,399

R50CC0312
3 stainless steel burners for 24,000 BTU
1 single control side burner for 10,000 BTU
Double walled stainless steel lid with cast aluminum end caps
500 square inches of primary cooking surface
175 square inch warming rack
Stainless steel control panel
Painted cart with double stainless steel doors
Stainless steel side tables with towel holder and tool hooks
3 burner level heat indicators
MSRP $1,399

R50SC0012
3 stainless steel burners for 24,000 BTU
18,000 BTU dual control side burner
Double walled stainless steel lid with seamless welds
500 square inches of primary cooking surface
175 square inch warming rack
2 internal halogen lights
Stainless steel control panel
Double door stainless steel cart
Stainless steel side tables with towel holder and tool hooks
3 burner level heat indicators
MSRP $999

Also available as a built-in model R50SB0412 configured for natural gas
MSRP $1,199

R33SC0012
2 stainless steel burners for 16,000 BTU
Double walled stainless steel lid with seamless welds
330 square inches of primary cooking surface
115 square inch warming rack
Stainless steel control panel
Single door stainless steel cart
Stainless steel side tables with tool hooks
2 burner level heat indicators
MSRP $999

R50CC0612
3 stainless steel burners for 24,000 BTU
Porcelain coated lid with cast aluminum end caps
500 square inches of primary cooking surface
175 square inch warming rack
Stainless steel control panel
Double door painted cart
Painted side tables with tool hooks
Lid mounted heat indicator
MSRP $799

R33CC0312
2 stainless steel burners for 16,000 BTU
Double walled stainless steel lid with cast aluminum end caps
330 square inches of primary cooking surface
115 square inch warming rack
Stainless steel control panel
Painted cart with single stainless steel door
Stainless steel side tables with tool hooks
2 burner level heat indicators
MSRP $799

Share →